亚洲精品久久久久久中文字幕|国产美女被遭强高潮网站不再|天天做日日做天天添天天欢公交车|国产精品久久久久久一级毛片

粘度計|旋轉粘度計廠家|運動粘度計|烏氏粘度計廠家_上海標卓

主頁 > 使用方法 >

粘度計英文使用說明書

 

This instrument is widely supplied in measuring axunge paint plastic, food, medication, adhesive, cosmetic and so on like fluidic sticky resistance and liquid absolute viscosity.fix and measuring must be done according requirement from instruction book。
 
Main technic spec
 
·Range of measure:10~105mpa.s
·Rotate speed: 6,12,30,60turn/minute
·Error of measure:±5%(Newton liquid)
·Power:220V±10%
         50Hz
 
Fix

1.     take out chassis base
andsupport from packing
boxcircumrotate three
level 。
2.adjust foot into tapping
hole in chassis base(chart 1)
3.main machine fix:
a. take out main machine by unscrewing the screws in chassis
b. unscrew the handle root screw . inset the power line into handle slot(chart2)
c. penetrate the handle into hole under slot(chart2)
d. screw the handle fix knob to screw the handle and keep the main machine level mostly (chart3)
 
 
8.measure the temperature of measured liquid directly , do not use the temperature value of constant temperature bath
9. it is normal when the viscosity changes because of change of speed and length of measure time during measuring. That is not the instrument hitch.
10.operate seriously according the operation manual
 
 

The whole set

1.main machine————————1
2.(1,2,3,4)rotors———— 1
3.protective support—————— 1
4.support——————————  1
5.lever adjustment screw———— 3
6.manual——————————  1
7.certificate ————————— 1
 
Quotiety table
 
     Run/minute
rotor
60 30 12 6
1 1 2 5 10
2 5 10 25 50
3 20 40 100 200
4 100 200 500 1000
 

 

Notice

1.this instrument should be used in 10—30
2.protective support must be fixed when measuring, or the viscosity value will change as the change of diameter of container
3.the rotor connective screw staff should be raised when fix or remove rotor, or the head of shaft will be damaged. Keep the bleb from rotor when rotor is immerged into liquid
4.the instrument should not be placed in oblique or inverse direction. Especially the rotor is fixed.
5.after fixing the rotor, do not turn on machine to turn the rotor without immerging the rotor into liquid
6.remove rotor carefully after finishing work every time.  Clear it extremely, dry is with blower, and put it back on the rotor support in vertically
7.pointer lock staff should be packaged by yellow package cover and rubber hand when carrying the instrument.
 


 
e. remove the rubber hand from pointer lock staff and yellow package cover from main machine inferior part.
alarm: do not turn on machine before removing the above two objects or it will damage the machine
power on, adjust the level adjustment foot(chart4). Make the bleb in the middle of level set(chart5).
 
Operation
 
1.first rightly rotate the protective support into the instrument inferior part.
2.prepare the liquid for measuring, select the column container having diameter not less than 70 mm
3.control the temperature in liquid for measuring correctly according the precision required by measuring
4. select the right rotor number by estimating the approximate range of viscosity of liquid or measuring, and rotate left the rotor into the connective screw staff(chart4),then rotate the up and down knob(chart5),make the instrument down slowly, immerging into measured liquid gradually, until the rotor liquid level balances the liquid level(chart4).put down the pointer lock staff, power on, relax.

the pointer lock staff,
to make the rotor
circumrotate in the
liquid. The speed is
20-30 run, until the
pointer stay at one
position . put down
the pointer lock staff to
make the reading unchangeable,
then turn off the motor to
make the pointer stay
in the range of reading
window,then get the
reading directly. If the
pointer do not stay in
the frame after turning
off motor, go on to put
down the pointer lock
staff. Repeat the action 
of turning on and off to
make the pointer in the
frame of window. If
selecting 6 and 12 turn /minute,
get the reading directly
without locking the pointer.5.the best is that the read pointer stay 30—90 division range, or change the rotor number or run speed to get the requirement 6.when you can not predict the viscosity value of liquid for measuring , the rotor and turn speed knob should be selected by turning from little value to big value, and from slow to fast, to measure the viscosity value.
 
 
Quotiety  and error correcting
1.the absolute viscosity value of liquid measured can be get by multiplying the reading pointed on dial when measuring and quotiety in quotiety table
that is:
η(mpa.s=k×α
k= quotiety
α=pointer reading
η=viscosity value
2.frequency error correcting
                                     normal frequency
actual viscosity value= indicated value ×—————————
                              actual frequency
 
 

 

Range stable and quotiety table

range stable
rotor Turn/minute
60 30 12 6
1 100 200 500 1000
2 500 1000 2500 5000
3 2000 4000 10000 20000
4 10000 20000 50000 100000
 
 
 

 


[上一篇:烏氏粘度計原理及其應用 ]    [下一篇:美國 BROOKFIELD博勒飛粘度計使用說明書 ]

使用方法

常見問題

瀏覽更多同類產品

STM-IVB斯托默粘度計
STM-IVB斯托默粘度計
 NDJ-1E 旋轉粘度計
NDJ-1E 旋轉粘度計
NDJ-1D 布氏旋轉粘度計
NDJ-1D 布氏旋轉粘度計
烏氏粘度計
烏氏粘度計
人妻激情偷乱一区二区三区 | 亚洲性无码av在线欣赏网| 小箩莉末发育娇小性色xxxx| 伊人久久大香线焦av综合影院 | 婷婷综合久久中文字幕蜜桃三电影| 色噜噜久久综合伊人一本| 国产性天天综合网| 日本免费a级毛一片| 国产精品无码专区av在线播放| 日韩精品无码专区免费播放| 一本一道av中文字幕无码| 99精品众筹模特自拍视频| 国产av在线www污污污十八禁| 亚洲色自偷自拍另类小说| 成人免费无码大片a毛片抽搐色欲| 人妻av无码一区二区三区| 亚洲av一二三区成人影片| 亚洲多人视频在线观看| 国产精品久久久久久久久久红粉| www夜片内射视频在观看视频| 西西大胆午夜人体视频| 色窝窝免费一区二区三区| 人人摸人人搞人人透| 午夜一区欧美二区高清三区| 国产精品久久一区二区三区| 久久精品网站免费观看| 老熟女hdxx老小配| 少妇被猛男粗大的猛进出| 亚洲第一女人天堂av| 欧美午夜精品一区二区三区电影| 99e久热只有精品8在线直播| 777精品久无码人妻蜜桃| 国色天香精品一卡2卡3卡4| 一本一道色欲综合网| 国产精品久久久久久爽爽爽| 又大又紧又粉嫩18p少妇| 日本一区二区中文字幕在线| 国产欧美精品区一区二区三区| 欧美性色欧美a在线播放| 免费看国产美女裸体视频| 久久久久亚洲av无码网站|